Erreur de configuration de VirtualBox rcvboxdrv «Mauvaise configuration d'argument»

29

Après avoir mis à niveau le noyau, VirtualBox, comme d'habitude, s'est plaint que le pilote du noyau Linux VirtualBox (vboxdrv) n'était pas chargé, et j'ai dû exécuter la commande suivante:

sudo /sbin/rcvboxdrv setup

Malheureusement, cette fois, l'exécution de l' rcvboxdrv setupéchec avec le message Bad argument setup. Je suppose que c'est un bogue de régression introduit dans le récent paquet VirtualBox sur la page d'Oracle.

Comment résoudre le problème et pouvoir exécuter VirtualBox?

virtualbox 
— Adam Ryczkowski
source
3
Pour moi, courir a sudo apt-get install --reinstall virtualbox-5.0résolu le problème.
— Takkat

Réponses:

42

À partir d'un commentaire sur le ticket , exécutez la commande suivante:

sudo /usr/lib/virtualbox/vboxdrv.sh setup

au lieu de la commande donnée par VirtualBox.

— xofer
source
2
Fonctionne, mais doit être exécuté après chaque redémarrage.
— winchendonsprings
Je n'en ai pas /usr/lib/virtualbox/du tout. Nouvelle installation de virtualbox. J'en ai un /usr/lib64/virtualbox/mais sans vboxdrv.sh. Installé à partir des dépôts Fedora 24.
— jozxyqk
3

Jusqu'à ce que cela soit résolu, vous pouvez éditer le /sbin/rcvboxdrvfichier (par exemple dans un terminal utilisant l'éditeur Nano via sudo nano /sbin/rcvboxdrv) et ajouter quelques lignes:

[…]
while test -n "${1}"; do
    case "${1}" in
        --nostart)
            START=
            ;;
        # START Workaround for https://www.virtualbox.org/ticket/15055
        setup)
            /usr/lib/virtualbox/vboxdrv.sh setup
            ;;
        # END
        *)
            echo "Bad argument ${1}" >&2
            exit 1
            ;;
    esac
    shift
done
[…]

Utilisez CTRL + O pour enregistrer les modifications. Après cela, vous devriez pouvoir exécuter à sudo /sbin/rcvboxdrv setupnouveau.

— Florian
source
3

J'ai eu le même problème sur Kubuntu 14.04.3 avec VirtualBox 5.0.14. Aucune des réponses précédentes n'a fonctionné mais le commentaire de @ Takkat suggérant

sudo apt-get install --reinstall virtualbox-5.0

travaillé pour résoudre le problème.

— Fabian Rost
source
1

J'ai eu le même problème sur Redhat7. Trouvé une suggestion sur un autre forum pour exécuter: /usr/lib/virtualbox/vboxdrv.sh setup Cela a résolu le problème. ma virtualbox fonctionne maintenant.

— D Sebastian
source
0

Il y a une solution:

La restauration /sbin/rcvboxdrvde l'ancienne version corrige le problème. Dans le cas où l'ancienne version du fichier ne vous serait plus disponible, voici la copie:

#! /bin/sh
# Oracle VM VirtualBox
# Linux kernel module init script

#
# Copyright (C) 2006-2015 Oracle Corporation
#
# This file is part of VirtualBox Open Source Edition (OSE), as
# available from http://www.virtualbox.org. This file is free software;
# you can redistribute it and/or modify it under the terms of the GNU
# General Public License (GPL) as published by the Free Software
# Foundation, in version 2 as it comes in the "COPYING" file of the
# VirtualBox OSE distribution. VirtualBox OSE is distributed in the
# hope that it will be useful, but WITHOUT ANY WARRANTY of any kind.
#

# chkconfig: 345 20 80
# description: VirtualBox Linux kernel module
#
### BEGIN INIT INFO
# Provides:       vboxdrv
# Required-Start: $syslog
# Required-Stop:
# Default-Start:  2 3 4 5
# Default-Stop:   0 1 6
# Short-Description: VirtualBox Linux kernel module
### END INIT INFO

PATH=/sbin:/bin:/usr/sbin:/usr/bin:$PATH
DEVICE=/dev/vboxdrv
LOG="/var/log/vbox-install.log"
VERSION=5.0.12
MODPROBE=/sbin/modprobe

if $MODPROBE -c | grep -q '^allow_unsupported_modules  *0'; then
  MODPROBE="$MODPROBE --allow-unsupported-modules"
fi

[ -f /etc/debian_release -a -f /lib/lsb/init-functions ] || NOLSB=yes
[ -f /etc/vbox/vbox.cfg ] && . /etc/vbox/vbox.cfg
export BUILD_TYPE
export USERNAME
export USER=$USERNAME

if [ -n "$INSTALL_DIR" ]; then
    VBOXMANAGE="$INSTALL_DIR/VBoxManage"
    MODULE_SRC="$INSTALL_DIR/src/vboxhost"
else
    VBOXMANAGE="/usr/lib/virtualbox/VBoxManage"
    MODULE_SRC="/usr/share/virtualbox/src/vboxhost"
fi
BUILDINTMP="$MODULE_SRC/build_in_tmp"
DODKMS="$MODULE_SRC/do_dkms"

# silently exit if the package was uninstalled but not purged,
# applies to Debian packages only (but shouldn't hurt elsewhere)
[ ! -f /etc/debian_release -o -x $VBOXMANAGE -a -x $BUILDINTMP ] || exit 0

if [ -n "$NOLSB" ]; then
    if [ -f /etc/redhat-release ]; then
        system=redhat
    elif [ -f /etc/SuSE-release ]; then
        system=suse
    elif [ -f /etc/gentoo-release ]; then
        system=gentoo
    fi
fi

[ -r /etc/default/virtualbox ] && . /etc/default/virtualbox

if [ -z "$NOLSB" ]; then
    . /lib/lsb/init-functions
    fail_msg() {
        echo ""
        log_failure_msg "$1"
    }
    succ_msg() {
        log_end_msg 0
    }
    begin_msg() {
        log_daemon_msg "$@"
    }
else
    if [ "$system" = "redhat" ]; then
        . /etc/init.d/functions
        fail_msg() {
            echo -n " "
            echo_failure
            echo
            echo "  ($1)"
        }
        succ_msg() {
            echo -n " "
            echo_success
            echo
        }
    elif [ "$system" = "suse" ]; then
        . /etc/rc.status
        fail_msg() {
            rc_failed 1
            rc_status -v
            echo "  ($1)"
        }
        succ_msg() {
            rc_reset
            rc_status -v
        }
    elif [ "$system" = "gentoo" ]; then
        if [ -f /sbin/functions.sh ]; then
            . /sbin/functions.sh
        elif [ -f /etc/init.d/functions.sh ]; then
            . /etc/init.d/functions.sh
        fi
        fail_msg() {
            eerror "$1"
        }
        succ_msg() {
            eend "$?"
        }
        begin_msg() {
            ebegin "$1"
        }
        if [ "`which $0`" = "/sbin/rc" ]; then
            shift
        fi
    else
        fail_msg() {
            echo " ...failed!"
            echo "  ($1)"
        }
        succ_msg() {
            echo " ...done."
        }
    fi
    if [ "$system" != "gentoo" ]; then
        begin_msg() {
            [ -z "${1:-}" ] && return 1
            if [ -z "${2:-}" ]; then
                echo -n "$1"
            else
                echo -n "$1: $2"
            fi
        }
    fi
fi

failure()
{
    fail_msg "$1"
    exit 0
}

running()
{
    lsmod | grep -q "$1[^_-]"
}

start()
{
    begin_msg "Starting VirtualBox kernel modules"
    if [ -d /proc/xen ]; then
        failure "Running VirtualBox in a Xen environment is not supported"
    fi
    if ! running vboxdrv; then
        if ! rm -f $DEVICE; then
            failure "Cannot remove $DEVICE"
        fi
        if ! $MODPROBE vboxdrv > /dev/null 2>&1; then
            failure "modprobe vboxdrv failed. Please use 'dmesg' to find out why"
        fi
        sleep .2
    fi
    # ensure the character special exists
    if [ ! -c $DEVICE ]; then
        MAJOR=`sed -n 's;\([0-9]\+\) vboxdrv$;\1;p' /proc/devices`
        if [ ! -z "$MAJOR" ]; then
            MINOR=0
        else
            MINOR=`sed -n 's;\([0-9]\+\) vboxdrv$;\1;p' /proc/misc`
            if [ ! -z "$MINOR" ]; then
                MAJOR=10
            fi
        fi
        if [ -z "$MAJOR" ]; then
            rmmod vboxdrv 2>/dev/null
            failure "Cannot locate the VirtualBox device"
        fi
        if ! mknod -m 0660 $DEVICE c $MAJOR $MINOR 2>/dev/null; then
            rmmod vboxdrv 2>/dev/null
            failure "Cannot create device $DEVICE with major $MAJOR and minor $MINOR"
        fi
    fi
    # ensure permissions
    if ! chown :root $DEVICE 2>/dev/null; then
        rmmod vboxpci 2>/dev/null
        rmmod vboxnetadp 2>/dev/null
        rmmod vboxnetflt 2>/dev/null
        rmmod vboxdrv 2>/dev/null
        failure "Cannot change group root for device $DEVICE"
    fi
    if ! $MODPROBE vboxnetflt > /dev/null 2>&1; then
        failure "modprobe vboxnetflt failed. Please use 'dmesg' to find out why"
    fi
    if ! $MODPROBE vboxnetadp > /dev/null 2>&1; then
        failure "modprobe vboxnetadp failed. Please use 'dmesg' to find out why"
    fi
    if ! $MODPROBE vboxpci > /dev/null 2>&1; then
        failure "modprobe vboxpci failed. Please use 'dmesg' to find out why"
    fi
    # Create the /dev/vboxusb directory if the host supports that method
    # of USB access.  The USB code checks for the existance of that path.
    if grep -q usb_device /proc/devices; then
        mkdir -p -m 0750 /dev/vboxusb 2>/dev/null
        chown root:vboxusers /dev/vboxusb 2>/dev/null
    fi
    succ_msg
}

stop()
{
    begin_msg "Stopping VirtualBox kernel modules"
    if running vboxpci; then
        if ! rmmod vboxpci 2>/dev/null; then
            failure "Cannot unload module vboxpci"
        fi
    fi
    if running vboxnetadp; then
        if ! rmmod vboxnetadp 2>/dev/null; then
            failure "Cannot unload module vboxnetadp"
        fi
    fi
    if running vboxdrv; then
        if running vboxnetflt; then
            if ! rmmod vboxnetflt 2>/dev/null; then
                failure "Cannot unload module vboxnetflt"
            fi
        fi
        if ! rmmod vboxdrv 2>/dev/null; then
            failure "Cannot unload module vboxdrv"
        fi
        if ! rm -f $DEVICE; then
            failure "Cannot unlink $DEVICE"
        fi
    fi
    succ_msg
}

# enter the following variables in /etc/default/virtualbox:
#   SHUTDOWN_USERS="foo bar"  
#     check for running VMs of user foo and user bar
#   SHUTDOWN=poweroff
#   SHUTDOWN=acpibutton
#   SHUTDOWN=savestate
#     select one of these shutdown methods for running VMs
stop_vms()
{
    wait=0
    for i in $SHUTDOWN_USERS; do
        # don't create the ipcd directory with wrong permissions!
        if [ -d /tmp/.vbox-$i-ipc ]; then
            export VBOX_IPC_SOCKETID="$i"
            VMS=`$VBOXMANAGE --nologo list runningvms | sed -e 's/^".*".*{\(.*\)}/\1/' 2>/dev/null`
            if [ -n "$VMS" ]; then
                if [ "$SHUTDOWN" = "poweroff" ]; then
                    begin_msg "Powering off remaining VMs"
                    for v in $VMS; do
                        $VBOXMANAGE --nologo controlvm $v poweroff
                    done
                    succ_msg
                elif [ "$SHUTDOWN" = "acpibutton" ]; then
                    begin_msg "Sending ACPI power button event to remaining VMs"
                    for v in $VMS; do
                        $VBOXMANAGE --nologo controlvm $v acpipowerbutton
                        wait=30
                    done
                    succ_msg
                elif [ "$SHUTDOWN" = "savestate" ]; then
                    begin_msg "Saving state of remaining VMs"
                    for v in $VMS; do
                        $VBOXMANAGE --nologo controlvm $v savestate
                    done
                    succ_msg
                fi
            fi
        fi
    done
    # wait for some seconds when doing ACPI shutdown
    if [ "$wait" -ne 0 ]; then
        begin_msg "Waiting for $wait seconds for VM shutdown"
        sleep $wait
        succ_msg
    fi
}

# setup_script
setup()
{
    stop
    DKMS=`which dkms 2>/dev/null`
    if [ -n "$DKMS" ]; then
      begin_msg "Uninstalling old VirtualBox DKMS kernel modules"
      $DODKMS uninstall vboxhost vboxdrv vboxnetflt vboxnetadp > $LOG
      succ_msg
    fi
    if find /lib/modules/`uname -r` -name "vboxpci\.*" 2>/dev/null|grep -q vboxpci; then
        begin_msg "Removing old VirtualBox pci kernel module"
        find /lib/modules/`uname -r` -name "vboxpci\.*" 2>/dev/null|xargs rm -f 2>/dev/null
        succ_msg
    fi  
    if find /lib/modules/`uname -r` -name "vboxnetadp\.*" 2>/dev/null|grep -q vboxnetadp; then
        begin_msg "Removing old VirtualBox netadp kernel module"
        find /lib/modules/`uname -r` -name "vboxnetadp\.*" 2>/dev/null|xargs rm -f 2>/dev/null
        succ_msg
    fi  
    if find /lib/modules/`uname -r` -name "vboxnetflt\.*" 2>/dev/null|grep -q vboxnetflt; then
        begin_msg "Removing old VirtualBox netflt kernel module"
        find /lib/modules/`uname -r` -name "vboxnetflt\.*" 2>/dev/null|xargs rm -f 2>/dev/null
        succ_msg
    fi  
    if find /lib/modules/`uname -r` -name "vboxdrv\.*" 2>/dev/null|grep -q vboxdrv; then
        begin_msg "Removing old VirtualBox kernel module"
        find /lib/modules/`uname -r` -name "vboxdrv\.*" 2>/dev/null|xargs rm -f 2>/dev/null
        succ_msg
    fi
    if [ -n "$DKMS" ]; then
      begin_msg "Trying to register the VirtualBox kernel modules using DKMS"
      if ! $DODKMS install vboxhost $VERSION >> $LOG; then
        fail_msg "Failed, trying without DKMS"
        DKMS=""
      fi
    fi
    if [ -z "$DKMS" ]; then
      begin_msg "Recompiling VirtualBox kernel modules"
      if ! $BUILDINTMP \
          --save-module-symvers /tmp/vboxdrv-Module.symvers \
          --module-source "$MODULE_SRC/vboxdrv" \
          --no-print-directory install >> $LOG 2>&1; then
          failure "Look at $LOG to find out what went wrong"
      fi
      if ! $BUILDINTMP \
          --use-module-symvers /tmp/vboxdrv-Module.symvers \
          --module-source "$MODULE_SRC/vboxnetflt" \
          --no-print-directory install >> $LOG 2>&1; then
          failure "Look at $LOG to find out what went wrong"
      fi
      if ! $BUILDINTMP \
          --use-module-symvers /tmp/vboxdrv-Module.symvers \
          --module-source "$MODULE_SRC/vboxnetadp" \
          --no-print-directory install >> $LOG 2>&1; then
          failure "Look at $LOG to find out what went wrong"
      fi
      if ! $BUILDINTMP \
          --use-module-symvers /tmp/vboxdrv-Module.symvers \
          --module-source "$MODULE_SRC/vboxpci" \
          --no-print-directory install >> $LOG 2>&1; then
          failure "Look at $LOG to find out what went wrong"
      fi
    fi
    rm -f /etc/vbox/module_not_compiled
    succ_msg
    start
}

dmnstatus()
{
    if running vboxdrv; then
        str="vboxdrv"
        if running vboxnetflt; then
            str="$str, vboxnetflt"
            if running vboxnetadp; then
                str="$str, vboxnetadp"
            fi
        fi
        if running vboxpci; then
            str="$str, vboxpci"
        fi
        echo "VirtualBox kernel modules ($str) are loaded."
        for i in $SHUTDOWN_USERS; do
            # don't create the ipcd directory with wrong permissions!
            if [ -d /tmp/.vbox-$i-ipc ]; then
                export VBOX_IPC_SOCKETID="$i"
                VMS=`$VBOXMANAGE --nologo list runningvms | sed -e 's/^".*".*{\(.*\)}/\1/' 2>/dev/null`
                if [ -n "$VMS" ]; then
                    echo "The following VMs are currently running:"
                    for v in $VMS; do
                       echo "  $v"
                    done
                fi
            fi
        done
    else
        echo "VirtualBox kernel module is not loaded."
    fi
}

case "$1" in
start)
    start
    ;;
stop)
    stop_vms
    stop
    ;;
stop_vms)
    stop_vms
    ;;
restart)
    stop && start
    ;;
force-reload)
    stop
    start
    ;;
setup)
    setup
    ;;
status)
    dmnstatus
    ;;
*)
    echo "Usage: $0 {start|stop|stop_vms|restart|force-reload|status|setup}"
    exit 1
esac

exit 0

J'espère que cela t'aides.

— Adam Ryczkowski
source
En utilisant notre site, vous reconnaissez avoir lu et compris notre politique liée aux cookies et notre politique de confidentialité.
Licensed under cc by-sa 3.0 with attribution required.